This is the most complete customization process of solid wood furniture you want!

This is the most complete customization process of solid wood furniture you want!

With the integration and upgrading of the building materials home furnishing market, the concept of whole wood customization has been accepted by many consumers, especially among the social elite, whole wood customization home decoration has become a fashion and trend.

01 design workflow

01-1 communication

Before the initial measurement: communicate with the salesperson (or the designer has participated in the communication with the customer in the sales process). Communication content: the customer’s product material, style, general category and quantity of the project, the customer’s personality preference, the scheduled measurement time, the customer’s address, and the relevant personnel who need to arrive

In the process of measurement: communicate with the customer or the person in charge of construction (try to keep the customer on site) communication content: the content, quantity, special requirements, suggestions and schemes requiring rectification of specific projects.

Dry goods sharing! This is the most complete whole wood customization process you want!

01-2 measurement

(1) Wood door measurement

Wooden door measurement (tools: tape measure, plan, water pen).

First communicate with the construction party or the customer, then measure, record in the place where the door opening will not be covered with marking notes, and finally copy.

Record standard: hole size (height * width * wall thickness) floor height.

Key points and precautions for measuring wooden doors:

① Elevation (accurate horizontal height and ceiling height);

② Position against the wall (whether the door pocket line is complete and whether it conflicts with the wall or other door pockets;

③ Whether there is stone or wallboard at the wall thickness position, and whether the thickness increases or not (the recording method is original wall thickness + increase stone thickness or wallboard foundation thickness + wallboard thickness;

④ For doors and covers with lintels and caps, pay attention to the floor height and contact angle (whether there is an internal corner line in the floor height);

⑤ Pay attention to the distance between the casing line and the wall and other casing lines (calculate the frame plate flying out and the line position);

⑥ Pay attention to the size error of each face of the opening;

⑦ Pay attention to the special requirements of customers for product size (such as light size);

⑧ Indicate the opening direction (such as glass door, yin-yang door);

⑨ Pay special attention to the hinge position and wall thickness of outdoor windows in the measurement of window sleeves;

⑩ If the track box is required not to be hoisted downward, pay attention to calculate the height of the door opening;

⑪ Pay attention to the installation method of hidden doors and hidden sliding doors;

⑫ Pay attention to the size and shape of the gate opening required for the shape of the pass.

Dry goods sharing! This is the most complete whole wood customization process you want!

(2) Wall panel measurement

Wall panel measurement (tools: tape measure, electronic measuring instrument, plan, water pen) first record the size in a prominent place on the wall, and then copy it.

Record standard: draw nodes on the wall in small size, overall size and special shape.

Key points and precautions for measuring wall panels:

① Elevation (accurate horizontal height, and ceiling height

② All dimensions inside the whole space should be recorded (such as: ceiling edge width, power supply position, hole position, etc.)

③ Communicate with floor materials and skirting materials (skirting lines that are particularly easy to ignore)

④ Pay attention to the center point of the ceiling

⑤ Pay attention to the relationship between the floor heights of each floor

⑥ Communicate the specific materials of each wall (such as stones for toilets and some public areas)

⑦ Pay attention to the material used for the internal corner line of the wall corner

⑧ Pay attention to the position that needs to be changed in foundation construction

⑨ Pay attention to the final position of the door opening or window opening

⑩ Pay attention to the dimension measurement method of external corner cladding column

Dry goods sharing! This is the most complete whole wood customization process you want!

(3) Cabinet type measurement

Cabinet type measurement (tools: tape measure, plan, water pen), key points and precautions for measuring cabinet type:

① Pay attention to the thickness of the wall, the position of the door pocket and the inlet and outlet water level;

② Pay attention to the position and height of the ceiling, the position of the smoke exhaust pipe and the position of the power socket

③ Pay attention to the height and position of the ceiling, the position of the light source or socket (especially the distance between the door and window sleeves of the system) when measuring the wardrobe in the cloakroom

④ Pay attention to whether the light source and water level are reserved in the wine cabinet

(4) Stair survey

Measurement of stairs (tools: tape measure, level gauge, setting out template, water pen), key points and precautions of measuring cabinet:

① Right angle stairs: step height, step width, step length, corner and platform width;

② Rotating stairs: step height, step width, step length, corner and platform width, radian setting out, twisting and flattening iron setting out;

③ Integral staircase: length, width, height, beam height and platform height of staircase;

④ The first run of stair steps is adjusted to an odd number, and the height of the first step of stairs without running is not higher than 150;

⑤ Pay attention to the triangle and skirting line;

⑥ Pay attention to whether the wall has wood finishes or other materials;

Dry goods sharing! This is the most complete whole wood customization process you want!

01-3 drawing deepening

The drawings of wooden doors are deepened (wooden doors are configured according to the customer’s needs, the standard style is applied, the module is replaced, and the window cover type is changed with the line type).

According to the size measured on the spot, adjust the proportion and configuration quantity of each wall surface with the best effect.

The cabinet type cabinet is defined according to the functional location and style, and the standard style is used.

For stairs, only one-sided drawings and reference pictures are initially made;

The ceiling type shall be adjusted according to the plane layout and the drawings after the elevation is deepened.

01-4 scheme discussion

Explain the characteristics of the deepened scheme to the customer in a professional manner, and do not modify the scheme completely according to the customer’s wishes.

Explain to the customer that the current construction is purely in conflict.

Cooperate with sales to press orders.

Dry goods sharing! This is the most complete whole wood customization process you want!

01-5 scheme modification

When the scheme needs to be modified, the time should not be too long.

For the key questions and dissatisfactions of customers, more than two sets of solutions should be deepened.

01-6 preliminary quotation

Standard format of quotation list: clearly display the location, specification, quantity, unit price and total price.

The quotation method depends on the local and customer conditions, such as whether the cabinet quotation is split or not?

The quantity of the list is not easy to deviate from the drawing. Try to be accurate (line plus loss).

Dry goods sharing! This is the most complete whole wood customization process you want!

01-7 business negotiation

Designers avoid discussing prices with customers. Assist the salesperson to sign the bill.

01-8 drawing of foundation

According to the basic drawing requirements of the exhibition hall design, simple details. Technical disclosure is required when the foundation drawings are handed over to the construction party, and the construction party is required to sign for the bottom.

01-9 double ruler

According to the above measurement and size requirements, take photos on site to keep the bottom. If it is inconsistent with the foundation size, it is necessary to communicate with the construction party in time for rectification.

Dry goods sharing! This is the most complete whole wood customization process you want!

01-10 drawing refinement

After the drawing is refined, if there is a scheme adjustment, it must be confirmed by the customer, such as adding or deleting items. If it is inconsistent with the foundation size, it is necessary to communicate with the construction party in time for rectification.

01-11 breakdown order

01-12 installation instructions

Key disclosure for special positions; Disclosure of installation height of wallboard.

01-13 completion acceptance and archiving

In order to ensure the perfect effect, the designer should be responsible for the effect. It is necessary to take photos of the case.

01-14 project summary

Customer’s summary of designer’s evaluation.

Summary of the shortcomings of the actual effect.

Post event summary of errors.

Dry goods sharing! This is the most complete whole wood customization process you want!

02 product deepening and order splitting

02-1 drawing refinement

Do you need to have the final foundation completion size and complete photos on site before drawing adjustment?

Check whether the measurement chart data is clear? Data with questions, loopholes and missing items need to be re measured!

In the drawing, the lines of basic dimensions are represented by red bold lines.

(1) Top view adjustment precautions

① Whether the spacing size is consistent with the total factory size (too much difference proves that there is error in re sizing)

② Whether the thickness of the wall or the depth dimension of the concave wall has been added with the thickness of the wallboard (whether to add the thickness of the wallboard is generally indicated in the double ruler)

③ Refine the product node diagram with cabinet, door, door pocket, curtain box cover, external corner of the wall or wrapped column position

④ Where there is a set line, pay attention to the distance between the set line and the wall on the opposite side of the room. If it is not enough, can you adjust or change the size of the set line

Dry goods sharing! This is the most complete whole wood customization process you want!

(2) Precautions for ceiling drawing adjustment

① Relationship between ceiling and background alignment (if not, it is necessary to remind Party A)

② Whether there is any conflict between the air outlet, light source and ceiling products, or has an impact on the installation and production of products (if any, it also needs to coordinate with Party A)

③ After adjusting the size, refine the node diagram of the ceiling and the product

④ After the drawing is adjusted, the ceiling drawing must be mirrored and changed into a bottom view

(3) Precautions for elevation adjustment

① Adjust according to the adjusted top node diagram and the measured size at the same time

② Pay attention to whether there are conflicts between sockets, switches and products (if there are conflicts, whether they can be handled on site or coordinated with Party A)

③ Whether the dimensions of the equipment related to the products provided by Party A are complete and accurate, and whether there are conflicts (such as furniture, wall lamps, soft bags, electrical appliances, etc.)

④ Whether the skirting line of all rooms goes with the ground? Yes, the customer needs to provide the size. (whether the top line goes through where the cabinet goes to the top)

⑤ Pay attention to whether the rechecked dimension floor height is the finished surface (floor panel specification) (whether there is a drop in floor height)

⑥ The position of the wall panel against the wall shall be reserved according to the installation method

⑦ Pay attention to the relationship between the background and the ceiling

⑧ Check whether the elevation and line specifications of each elevation are unified

Dry goods sharing! This is the most complete whole wood customization process you want!

02-2 product split

(1) Precautions for splitting wallboard

① Split lines are represented by thick pink lines

② When disassembling, the specification should not be too large or too trivial

③ Pay attention to the relationship and size of the transfer and handover positions (the external corners are assembled!)

④ The joint position shall be avoided to expose as little as possible

⑤ Try to code the number according to the floor, room and quantity. For example, if the bedroom on the second floor, make 2w-01

⑥ The numbering sequence shall be centralized according to the same category, the identical product numbers shall be unified, and the quantity shall be indicated in the order

⑦ The number font needs to be highlighted and easy to identify. It is best to cover the background and place it correctly

⑧ Check whether the number of wallboard blocks is missing

(2) Precautions for line class splitting

① Lines need to be broken down according to the size of each room to minimize joints (the length needs to consider transportation and handling upstairs)

② Conventional lines need to be prepared (loss or damage)

③ Small external corner lines need to be combined in the factory

④ Thickness relationship between waist line, skirting line and door pocket line

⑤ Pay attention to the direction of special-shaped lines and try not to disassemble them

⑥ Irregular large carved lines calculate the alignment position

Dry goods sharing! This is the most complete whole wood customization process you want!

(3) Precautions for wood door splitting

① Pay special attention to whether the wall thickness has the thickness of wallboard (height / width / wall thickness / door)

② Where there is a dado, the door and window casing lines need to be buckled or closed

③ The opening direction of child and mother door, double door and art glass door shall be specially indicated

④ If customers have special requirements for door leaf or light size, please pay attention to conversion

⑤ Pay special attention to the color and direction of yin and Yang doors

⑥ Distance between hat head and line and wall

(4) Precautions for cabinet disassembly

① Conventional product parts can be marked with codes or words, and unconventional product parts need to be disassembled

② The cabinet reaching the top shall be split by the movable top line as far as possible, or the upper and lower cabinets shall be divided into backup and closing lines (otherwise the cabinet will not reach the top)

③ Whether the specifications and dimensions of cabinet hardware equipment are consistent (such as metal basket, pants rack, lattice drawer, dressing mirror, safe, etc.)

④ After refining the internal functions of the cabinet, it needs to be confirmed by the customer (adjusted according to the customer’s requirements)

⑤ Consider whether the cabinet installation is blocked

Dry goods sharing! This is the most complete whole wood customization process you want!

(5) Precautions for drawing and ordering

Sometimes it is necessary to specify the Order Description: materials, paint process requirements, woodworking process requirements, factory hardware configuration, packaging and transportation requirements, installation process requirements, etc.

① On the first page of the drawing, prepare the general order specification according to the requirements of the contract and the customer after communication

② The drawings must be concise and clear, with clear data and clear remarks (each drawing is not easy to be too full or too small)

③ The numbering sequence of drawings should be in accordance with the sequence (such as: wall panels, lines, wooden doors, cabinets)

④ Before placing an order, the drawings must be printed out for review (check whether the font size and graphics of the drawings are clear, and whether the marked dimensions are deviated and shifted. After the review, the drawings are exported to the factory in JPG format (the image format avoids changes in the electronic version, but ensure that the printed version is clear) and the electronic document is used as a reference

⑤ After finishing the list, the orderer in the factory needs to check whether the list is consistent with the drawing (generally, there are separate orderers in the factory)

Dry goods sharing! This is the most complete whole wood customization process you want!

03 standardized drawing process

03-1 analysis of structural problems (Technology)

03-2 three character analysis

Interface analysis

Obstacle analysis

Hidden risk analysis

  1. Aesthetic design (assist in design from the perspective of aesthetics)
  2. Understand the user’s personality characteristics and preferences
  3. Users’ living habits (improve the design through life)
  4. Users’ aesthetic views (style design)
  5. User’s family structure (functional design)
  6. Analysis of overall environmental conditions
  7. Consider the yield
  8. Transportation, packaging, installation, maintenance, etc

About author View all posts

admin

Leave a Reply

Your email address will not be published. Required fields are marked *